Is it possible to take photos and videos using Bluetooth Remote Shutter Portable Selfie Clicker for DSLR?

DSLR remote control app

Using the blutooth camera shutter it is not possible for you to capture photos or record videos as DSLR s do not come with inbuilt bluetooth.

,Some cameras have Infrared technology in which infrared remotes could be used or if you smartphone has an IR blaster it could be used.

,In the market or ecommerce websites some remotes are available which could be connected with the camera to control it.

,You.

.

.

Canon camera Remote control app

Well, it depends on the DSLR and the smartphone you have.

,Most Nikons support a remote control app called u2018DSLR Control that enables a USB Host (OTG) enabled smartphone to act like a viewfinder enabled remote controller.

,DSLR Control - Camera Remote Controller - Apps on Google PlayFor Nikons with WiFi, there is an app from Nikon itself that does pretty much the same thing.

,If your camera is a Canon, you may find a similar app for that also.

,Note, the limited data transfer rates available over the USB OTG or WiFi channels between camera and mobile doesnt allow live streaming of uncompressed video feed from the camera.

So while the video preview might be usable as a remote viewfinder, recoding of the same may not produce the full quality video.

Canon Remote Control

Remote Control RC-6If you want a small, versatile, inexpensive remote shooting accessory, look no further than the Canon Remote Control RC-6.

Despite its diminutive size (32 x 63.

5 x 6.

5mm), this device can be used for a number of different tasks.

,Camera compatibility: EOS 5D Mk II, 5D Mk III, 5DS, 5DS R, 6D, 7D, 7D Mark II, 60D, 60Da, 70D, 100D, 300D, 350D, 400D, 450D, 500D, 550D, 600D, 650D, 700D, 750D, 760D, M, M3, 10, 100, 30, 30V, 33, 33V, 50, 50E, IX.

,The RC-6 is a wireless transmitter (infrared rather than radio waves).

To work, it needs a receiver.

Unlike wireless controllers, the receiver for the RC-6 is already built into a range of EOS models (see right).

One reason the RC-6 is relatively inexpensive is that you are only buying half the system.

You have already paid for the other half u2013 if you have a compatible camera.

,It is not possible to buy a separate receiver for the RC-6.

If you do not have the right camera you will have to look at alternative methods for remote firing.

,As you can see above, the sensor for the RC-6 is on the front of the camera (EOS 550D shown, but the sensor is in a similar position on other compatible cameras).

,The RC-6 has a small hole in the bottom left corner for attaching a lanyard (not supplied).

,Using the RC-6The RC-6 is a very simple device, controlled by just a button and a switch.

Make sure the drive mode is set to remote control.

Aim the small black arrow in the silver circle at the camera and press the button to fire the shutter.

A switch on the back gives the option of immediate firing (u2018u2022u2019), or firing with a 2-second delay.

,Line of sightInfrared devices normally need to see each other u2013 often known as u2018line-of-sightu2019.

Based on this, it would seem that you can only use the RC-6 from in front of the camera, and you will find this quoted in some reviews.

But itu2019s not strictly true.

If you hold the RC-6 a few inches above the shutter release, aiming down, the shutter will fire when you press the remote button u2013 useful as an alternative to a remote switch.

It will even operate from behind the camera if the infrared beam is reflected back from a nearby surface.

,When aimed from the front of the camera the range is given as 5 metres, though this will vary with the surroundings.

,Infrared devices can be affected by fluorescent lighting, but we have not experienced any problems.

,Remote control nsensor on cameraRecording moviesYou can use the RC-6 to start and stop nmovie recording on the more recent EOS models.

As with all uses of the RC-6, make sure that the drive mode is set to one of the remote shooting options.

,Set the switch on the RC-6 to u20182u2019.

When you press the RC-6 button the recording will start immediately.

Pressing the button again will stop the recording.

If the switch is set to u2018u2022u2019, pressing the RC-6 button will take a still photo.

,This is a great little feature which we hope will be included in new EOS models.

,Bulb modeIf you shoot in bulb mode, pressing the camera shutter button opens the shutter.

It stays open for as long as you hold the button down u2013 not very convenient for exposure times of more than a few seconds.

,A remote switch is better.

You can press and lock the remote button so that you can move away from the camera while the exposure is in progress.

,But best of all is the RC-6.

Press the button on the remote control unit to open the shutter, press it again to close the shutter.

If you have the remote control set to 2-second delay, there will be a 2-second delay before the shutter first opens.

During the exposure a timer displays the time elapsed on the LCD screen.

If you have a camera compatible with the RC-6, using this technique is much easier than attaching a cable to the remote socket.

,Self portraitsAn obvious use for the RC-6 is for shooting self-portraits.

Set One-shot mode.

When you press to RC-6 button the camera will autofocus and then fire.

However, if you do not want to include the RC-6 in the image, set the RC-6 switch to 2-second delay.

Now when you fire the RC-6 at the camera you will have a couple of seconds to move the device out of the field-of-view before the picture is taken.

Canon remote control software

At the National Library of Sweden, we have a number of digitization stations that use the Canon 5D Mark II but most DSLRs will do.

The most important feature of your camera is live view and remote control software, since it makes it much more easy to control the camera and set the focus.

Its also important to remember that the focus will shift as you turn the pages.

,We have descibed our workflow is this article, http://www.

imaging.

org/IST/store/epub.

cfm?abstrid=43781 If you contact me, I can probably mail you a copy.

,The DIY-website that Marcus linked to is a good resource for information.

For software, ScanTailor (http://scantailor.

sourceforge.

net/) has received some praise but Ive never used it in our workflow.

Camera with Remote Control Zoom

Why? Thats not how films are made.

How can the actors concentrate on acting if they are also working the equipment?,Stop, think, start againu2026.

Canon remote control how to use

the remote is for your shutter button it works with infrared when you set your cameras drive mode to self timer 10sec/remote control or shutter speed to bulb mode then you can press button on remote to activate the shutter wirelessly,

Camera with remote shutter

I would suggest to define the requirements for the remote shutter and chose accordingly.

,Some remote shutter can work as an intervalometer, some can make the camera autofocus before the picture is taken, and so on.